Product Introduction The rotary sand dryer is professional drying equipment supporting dry-mix mortar production lines. It is mainly used to dry river sand, quartz sand, manufactured sand and other raw materials to reach the required moisture content for mortar batching. Adopting rotary drum ...
rotary sand dryer for mortar lines
,industrial rotary sand dryer machine
,rotary sand dryer with warranty
Product Introduction
The rotary sand dryer is professional drying equipment supporting dry-mix mortar production lines. It is mainly used to dry river sand, quartz sand, manufactured sand and other raw materials to reach the required moisture content for mortar batching. Adopting rotary drum structure, the material and hot air carry out sufficient heat exchange inside the cylinder. It features continuous feeding and discharging, stable operation and large processing capacity. It can be matched with hot blast stove, dust collector, conveyor and screening system to form a complete sand drying system, providing qualified dry sand raw materials for dry mortar, putty powder, tile adhesive and other production.
Core Highlights
- High thermal efficiency:Reasonable internal lifting plate design makes materials fully scattered and in full contact with hot air, which greatly improves drying efficiency and reduces fuel consumption.
- Wide adaptability:Suitable for various granular sand materials, not easy to block; the final moisture can be adjusted flexibly according to production requirements.
- Stable & durable:Thickened wear-resistant drum, high temperature resistant sealing structure, less failure, long service life, adapted to continuous heavy-load production of mortar plants.
- Environmental friendly design:It can be connected with supporting dust removal equipment to effectively control dust emission and meet environmental protection standards.
- Easy operation & maintenance:Independent temperature and speed control, simple parameter setting; convenient access for inspection and replacement of wearing parts.
Specification Parameters
| Item | Parameter |
|---|---|
| Model | Customized |
| Capacity | 1–20 t/h (optional) |
| Initial moisture | ≤20% |
| Final moisture | 0.5%–3% (adjustable) |
| Drum speed | 1–6 r/min |
| Heat source | Coal, biomass, natural gas, diesel, hot air furnace |
| Driving mode | Gear / chain drive |
| Supporting system | Hot blast stove, feeder, conveyor, dust collector |
Precautions
- Before startup, check the tightness of all connecting parts, sealing parts and transmission components to avoid air leakage and material leakage.
- Do not feed oversized impurities such as stones and iron blocks into the dryer to prevent damage to the lifting plates and drum.
- Gradually heat up the equipment; it is forbidden to run the machine under ultra-high temperature for a long time. Monitor the inlet and outlet temperature in real time.
- Regularly lubricate the bearing and transmission parts, and inspect the wear of lifting plates and seals.
- Stop feeding first before shutdown, and keep the drum rotating until the temperature drops to a safe level, then cut off the heat source and power supply.
- The dust removal system must operate synchronously; do not run the dryer without dust removal equipment.
Application Scenarios
- Dry-mix mortar production lines (raw sand drying for ordinary mortar, waterproof mortar, thermal insulation mortar, tile adhesive, self-leveling mortar)
- Sand and gravel processing plants, quartz sand production lines
- Building material factories, pre-mixed aggregate production
- Mineral, grain and other granular material drying with similar characteristics
FAQ
Q1: Can the final moisture of sand be adjusted?
A1: Yes. We can adjust the sand outlet moisture by changing feeding speed, hot air temperature and drum rotating speed according to your mortar formula requirements.
Q2: What heat sources are available for selection?
A2: Multiple heat sources are optional, including biomass, coal, natural gas, diesel oil, etc. We will recommend a suitable solution according to your local fuel cost and environmental requirements.
Q3: How to match it with my existing mortar production line?
A3: We can design the supporting feeding, conveying and dust removal scheme according to your site space, required output and existing equipment layout, to realize seamless docking with your mortar production line.
Q4: Is this dryer easy to be blocked?
A4: The specially designed lifting plate structure is good for scattering sand. As long as the feeding is uniform and large impurities are removed in advance, blocking rarely occurs.