Product Introduction Our frac sand dryer is a high-efficiency rotary drying equipment independently developed for proppant sand production lines, perfectly matched with our complete mortar and mineral processing production system. It is mainly used to remove surface and internal moisture of quartz ...
frac sand dryers for dry mortar
,industrial frac sand drying equipment
,frac sand dryers production line
Our frac sand dryer is a high-efficiency rotary drying equipment independently developed for proppant sand production lines, perfectly matched with our complete mortar and mineral processing production system. It is mainly used to remove surface and internal moisture of quartz frac sand, coated sand, construction sand and other granular materials. Adopting a rotary drum structure combined with hot air counter-current drying technology, it realizes continuous, stable and uniform dehydration of sand materials. The equipment can adapt to large-capacity continuous operation, effectively control the final moisture of sand, meet the strict moisture requirements of fracturing proppant, dry mortar aggregate and other finished products, and is an indispensable core host for frac sand processing and dry-mix sand production lines.

- High Drying Efficiency & Stable Moisture Control Counter-current heat exchange design, fully contact hot flue gas with sand grains; adjustable outlet moisture, stable finished moisture can reach below 0.5%, avoiding uneven drying and material agglomeration.
- Wear‑Resistant & Long Service Life The inner lining of the drum adopts thick wear-resistant liner and special lifting plate structure, which reduces the impact and abrasion of high-hardness quartz sand on the cylinder body; the main shaft and supporting roller are processed with heat treatment to adapt to long-term heavy-load operation.
- Energy‑Saving & Low Operating Cost Optimized air duct and heat distribution structure reduces heat loss; it can be compatible with coal, natural gas, biomass, diesel and multiple heating sources; equipped with waste heat recycling device to reduce fuel consumption.
- Good Dust Reduction & Environmental Protection Performance It can be connected with cyclone dust collector, baghouse dust collector and desulfurization and denitrification system, effectively capture sand dust, meet local industrial emission standards, and reduce material loss.
- Intelligent & Easy Operation Equipped with temperature, pressure and feeding online monitoring system; supporting frequency conversion speed regulation for drum and feeding, users can adjust feeding capacity, drum rotating speed and air temperature according to raw sand moisture; automatic interlock protection for overload and over-temperature.
- Modular Design, Easy Installation & Maintenance The whole machine adopts split modular structure, convenient for transportation and on-site assembly; the access cover is reserved for quick replacement of lifting plates and wearing parts, shortening downtime.
| Item | Parameter |
|---|---|
| Processing Capacity | 5–50 t/h (customizable) |
| Inlet Raw Sand Moisture | ≤18% |
| Finished Sand Moisture | 0.3%–0.8% (adjustable) |
| Drum Size | Φ1.2×10m / Φ1.5×12m / Φ1.8×14m / Customized |
| Drum Rotation Speed | 1–5 r/min, frequency control |
| Heating Mode | Coal / Natural Gas / Biomass / Heavy Oil / Light Oil |
| Driving Power | 15–75 kW |
| Working Temperature | 200–650℃ (hot air inlet, adjustable) |
| Applicable Material Size | 20–140 mesh frac sand, construction aggregate sand |
| Supporting System | Feeder, hot blast stove, dust collector, induced draft fan, electric control cabinet |
| Installation Form | Horizontal rotary type, inclined 3°–5° |
Note: We can redesign and customize the parameters according to your raw material condition, target output and local fuel cost.
- Before starting the machine, check the tightness of all connecting bolts, the lubrication status of supporting rollers, thrust rollers and gear transmission parts, and confirm that the dust removal pipeline and induced draft fan are unobstructed.
- Preheat the dryer gradually. Do not feed wet sand immediately after igniting the hot blast stove. Feed materials only when the drum internal temperature reaches the set working range to prevent material sticking and blockage.
- Keep the feeding uniform; avoid sudden large feeding volume or empty running for a long time. If the raw sand moisture fluctuates greatly, adjust the hot air temperature and drum speed in time.
- Regularly check the wear of lifting plates and wear-resistant liners. Replace severely worn parts in time to prevent uneven material lifting and reduced drying efficiency.
- Strictly prohibit flammable and explosive sundries from entering the drum. When using gas or oil burners, check pipelines and valves for leakage before startup.
- When shutting down, stop feeding first, keep the drum rotating and continue air supply until the materials inside the drum are completely discharged and the temperature drops naturally, then cut off the heat source and power supply.
- Daily clean the dust collector and pipeline sediment; regularly maintain the sealing parts of the feeding and discharging ends to prevent hot air leakage and dust overflow.
- Operators must receive professional training and follow the operation manual; set up safety protection covers and warning signs for rotating parts.
- Frac sand / proppant quartz sand production line for oil and gas fracturing
- Dry-mix mortar production line, drying of river sand, quartz sand and manufactured sand aggregate
- Coated frac sand processing, drying before resin coating
- Mineral sand, silica sand, foundry sand and other granular mineral drying
- Building material sand, thermal insulation sand and other bulk sand material dehydration
A: Under stable feeding, our dryer can stably control finished moisture between 0.3%–0.8%. If you have higher requirements for low moisture, we can optimize the hot air system and extend the drying section for your project.
A: Yes. Our frac sand dryer is designed to be matched with our full set of mortar and sand processing equipment. We can provide a complete turnkey scheme including feeding, screening, drying, dust removal, storage and batching.
A: Natural gas is preferred for clean emission; biomass fuel and coal are suitable for regions with low fuel cost. We will recommend the most economical heating solution according to your local fuel supply and environmental protection requirements.
A: Conventional models take about 25–40 days for production. Installation and commissioning generally take 7–15 days depending on the site layout; we can send engineers to your site for guidance.
A: We provide one-year warranty for the main host (excluding wearing parts). We supply long-term spare parts, offer remote technical support, and support on-site installation guidance, commissioning and operator training.
A: Yes. The hot air temperature, drum speed and induced air volume are adjustable on the electric control system. For large span capacity upgrading, we can also provide scheme transformation services.