Product Introduction This complete dry mortar production line is an integrated set of building material processing equipment, supporting the production of various dry-mixed mortars. It adopts a modular design and integrates raw material silo storage, sand drying and screening, automatic batching & ...
dry mortar production line
,concrete production line equipment
,dry mortar mixing equipment
This complete dry mortar production line is an integrated set of building material processing equipment, supporting the production of various dry-mixed mortars. It adopts a modular design and integrates raw material silo storage, sand drying and screening, automatic batching & weighing, twin-shaft gravity-free mixing, finished material temporary storage, automatic bagging/bulk discharging, pulse dust collection and PLC intelligent control system. The whole process realizes fully automatic production from sand, cement, fly ash and additives to finished dry mortar.
Three layout types are available: tower type, step type and simple type, which can match different site conditions and investment budgets. The line stably produces masonry mortar, plastering mortar, floor mortar, tile adhesive, putty powder, thermal insulation mortar, self-leveling mortar and other products. It replaces on-site manual mixing, featuring stable formula ratio, controllable dust emission and high production efficiency. It is widely installed in building material factories, supporting workshops of commercial concrete plants and mortar processing projects in construction industrial parks.
- High-precision weighing & stable quality Independent weighing modules are equipped for main materials, powder materials and trace additives. The weighing accuracy for main materials reaches ±1%, and trace additives can reach ±0.5%. Multiple formulas can be saved and switched with one click, ensuring high uniformity and consistent performance of mortar batches.
- Superior mixing performance & high efficiency The core unit is a twin-shaft gravity-free mixer. One batch can be finished within 3–5 minutes with no dead mixing zones and no material agglomeration. Wear-resistant liners extend service life, supporting flexible switching between lightweight thermal insulation mortar and heavy-duty ordinary mortar.
- Intelligent automation & labor saving Adopts PLC + touch screen centralized control. It supports formula storage, production data recording, traceability and fault alarm. Automatic batching, conveying and bagging reduce on-site operators; only 1–2 staff are required for routine duty to cut labor costs.
- Closed environmental protection design All material conveying sections are fully enclosed and matched with pulse bag dust collectors to meet dust emission standards and reduce workshop dust pollution. An optional sand drying system controls sand moisture content ≤0.5% to prevent caking of dry mortar.
- Customized configuration & strong adaptability The production capacity, layout and discharging modes (valve bag packing, open bag packing, bulk loading) can be customized. The simple version suits small-scale new projects; the tower type covers a smaller area with lower energy consumption for large-scale mass production.
- Easy maintenance Modular structure with standardized wearing parts and reserved maintenance space. We provide on-site installation, commissioning, operation training and after-sales technical support.
| Item | Parameter |
|---|---|
| Model | DM-50 Dry Mortar Production Line |
| Theoretical Capacity | 50 t/h, annual output about 200,000–250,000 tons |
| Main Mixer Type | Twin-shaft Gravity-free Mixer |
| Effective Mixing Volume | 4000 L |
| Batch Mixing Capacity | 2.4 t per batch, mixing cycle 3–5 min |
| Total Installed Power | Approx. 110 kW (excluding optional dryer) |
| Batching Silos | Sand silo, cement silo, fly ash silo, additive silo |
| Weighing Accuracy | Sand & cement ±1%; micro additives ±0.5% |
| Dust Removal | Pulse Bag Dust Collector |
| Control System | PLC automatic control system with touch screen |
| Discharge Method | Automatic valve bag packing machine + bulk outlet (optional) |
| Compressed Air Requirement | 0.4–0.7 MPa |
| Layout Type | Tower / Step / Simple Type for selection |
| Optional Modules | Three-pass sand dryer, vibrating screener, automatic palletizer |
- Pre-start inspection: Check conveyors, pneumatic valves, load cells, dust collector and air compressor before startup. Clean caked residues inside the mixer. Make sure silo gates and seals are intact. Do not impact or apply heavy pressure on weighing sensors.
- Raw material management: Strictly control sand moisture. Wet sand must go through the drying system. Store additives separately in dry conditions to avoid moisture failure and caking. Hard metal foreign objects are forbidden to enter the mixer.
- Production operation: Use saved authorized formulas and do not modify ratios arbitrarily. Never put hands or tools into the mixer or elevator during operation. Cut off power and hang warning signs for maintenance work.
- Daily maintenance: Clean residual powder inside the mixer and packing machine after each shift. Check abrasion of blades and liners regularly and add lubricant on schedule. Clean dust filter bags periodically to avoid blockage, poor negative pressure and dust leakage.
- Safety & environment: Keep the workshop well ventilated and equipped with fire-fighting facilities. The electric control cabinet needs waterproof and dustproof protection. Keep pipelines and silos warm in winter to prevent powder arching and poor discharging.
- Long-term shutdown storage: Empty all silos and the mixer completely, remove dust and apply anti-rust treatment.
- Professional dry mortar manufacturers for mass production of masonry, plastering and floor mortar.
- Special mortar processing plants for tile adhesive, interior & exterior putty, inorganic thermal insulation mortar, repair mortar and self-leveling mortar.
- Commercial concrete batching plants, adding mortar production lines for integrated operation of concrete and dry mortar.
- Construction groups and industrial parks with self-built mortar bases for centralized material supply.
- Export-oriented building material factories and industrial parks for standardized bagged mortar export.
- Small and medium building material processors adopting simple lines for low-investment startup.
A: Concrete batching plants produce wet ready-mix concrete mixed with water. This dry mortar line produces dry-mixed powder mortar. All raw materials are dried and mixed, packed in bags or delivered in bulk, and mixed with water on construction sites. It requires higher precision for micro additive metering.
A: Yes. Multiple formulas can be stored and switched quickly. However, clean the mixer thoroughly when switching between different mortar types (e.g. ordinary mortar to thermal insulation mortar) to avoid cross-contamination and performance defects.
A: Simple type: 300–500 ㎡; Step type: 600–1000 ㎡; Compact tower type (50t/h): 400–600 ㎡. The tower type requires higher workshop height.
A: It depends on raw sand moisture content. Natural river sand usually has high moisture and needs drying. Well-dried manufactured sand with qualified moisture can skip the dryer module to reduce investment.
A: Closed conveying plus pulse dust collection keeps dust concentration within the standard range under normal operation. Routine maintenance of filter bags and sealing parts ensures compliance with environmental requirements.
A: Simple type: 7–15 days; Tower type complete line: 20–40 days (including foundation pouring, hoisting, commissioning and training).
A: Main consumables include mixing blades, wear liners, packing nozzles, dust filter bags and sealing gaskets. Parts are standardized and available for long-term supply.